Guaranteed safe checkout
Total price R 5,570.00
Two-Step Correction
Piano black trim is notorious for showing every fingerprint, dust particle and fine swirl almost immediately after cleaning. This dedicated two-step system from Soft99 addresses all three problems in sequence - lifting contamination and reducing swirl marks with the cleaner, then locking in depth and hydrophobic protection with the coating step.
Why It Works
Four reasons professional detailers reach for this kit on piano black panels.
The cleaner step reduces fine swirl marks and scratches on gloss black plastic that make trim look dull and scratched.
The coating leaves a hydrophobic layer that causes water to bead and sheet, keeping the trim cleaner between details.
The sealed surface resists fingerprints and dust adhesion, so piano black stays presentable far longer after each clean.
Developed for gloss black plastic from the ground up, not adapted from a paint product, so compatibility and results are reliable.
How It Compares
A lot of detailers reach for whatever trim dressing is on the shelf when piano black looks flat. Here is how this dedicated correction-and-protection kit compares to a typical off-the-shelf gloss trim product.
| Feature | DetailerSA | Alternative |
|---|---|---|
| Reduces fine swirl marks on gloss plastic | Yes | No |
| Formula developed specifically for piano black plastic | Yes | No |
| Hydrophobic, fingerprint-resistant finish | Yes | Yes |
| Two-step correction then protection sequence | Yes | No |
| Safe for use on gloss black plastic trim | Yes | Yes |
| Suitable for painted bodywork correction | No | No |
Built for Plastic
Most correction and protection products are developed for painted surfaces and then applied to trim as an afterthought. Soft99 built this kit specifically for piano black plastic, which means the chemistry is matched to the surface and you are not risking a formula that was never intended for it.
Reviews
Piano black pillars on the hatch were a mess of hairline swirls - looked grey in sunlight. After the cleaner step they went back to proper black, and the coating has kept fingerprints off for weeks.
Tried this on the gloss black grille surround and the centre console inserts in one session. Both came up well. The console needs a second pass if the swirls are deep, but the exterior trim was sorted in one go.
Gloss black trim attracts every fingerprint and scratch going. This kit addresses both problems - cleaner pulls out the haze, coating keeps it looking sharp between washes. Compact enough to keep in the detailing kit for regular top-ups.
Questions
This kit is formulated for gloss black plastic trim surfaces - piano black pillars, grille surrounds, mirror caps, centre consoles, dashboard panels and door trim strips. It is not designed for painted bodywork, glass or rubber seals, so keep it on hard gloss plastic only.
Apply a small amount of the cleaner to a soft, clean microfibre cloth and work it into the trim using light, overlapping passes. Allow it to haze slightly, then buff off with a fresh microfibre. This lifts surface contamination and reduces fine swirl marks before the coating step goes on.
Once the cleaner has been fully buffed away, apply the coating step to the surface, allow it to haze - typically a short flash time in normal conditions - then buff it clear with a clean, dry microfibre. Work in small sections so the coating does not over-cure before you buff it off.
No. The formula is developed specifically for gloss black plastic and is not intended for use on painted panels. If you want to correct and protect painted surfaces, use a compound and sealant combination suited to automotive paint.
The source does not state a specific durability period. As a hydrophobic coating on plastic trim, longevity will depend on how often the surface is cleaned and whether it is exposed to direct sunlight or harsh chemicals. Reapply when water no longer beads or the gloss starts to look flat.
No. The cleaner step is designed for hand application with a soft microfibre cloth. Piano black trim is often in tight, shaped areas where a machine polisher would be impractical, so the hand-application method is intentional and effective on these surfaces.
If the trim already has an intact ceramic coating, the Soft99 cleaner step may reduce the ceramic layer's hydrophobic properties. It is best to use this kit when you are starting fresh or when a previous coating has worn away and the trim needs correction and re-sealing from scratch.
Once both steps are complete, the trim should show restored depth and a mirror-like gloss, noticeably cleaner-looking than before. The hydrophobic layer means fingerprints and dust do not cling as readily, so the finish stays presentable much longer between wipes.
